Oil mist separator type OUPC 500 - 1010

Compakt multi-stage filter for cooling lubricants for mounting directly on processing machines. For filtration of oil mist, emulsion mist, minimal quantity lubrication and oil smoke.
Compact filter unit for cooling lubricants for mounting on top of metalcutting processing machines. The 4 separation stages of the filter ensure versatile application. Sepeation degree min. 99.95% of all cooling lubricant particles. Separated particles are led back to machine again if required.
H13
Filter class

Product Features

  • Poluted air is led in at the separator end to pre-separation chamber for air distribution and densification
  • The accumulated particles are led on to the washable pore filter PPi35 (50% higher eifficiency than alu-grease filter)
  • Then the air is fine-filtrated in cartridge filter type G104A. Separation degree > 99% af particles above 0.1µm
  • Beneath the first two filter stages a fluid reservoir with ½”-drain coct is located
  • Last filter stage is a HEPA-filter, filter class H13 that ensures removal of >99.95% smoke particles down to 0.1µm

Product Highlights

Capacities

Air volume 500 / 510: Up to 500m³/h
Air volume 1000 / 1010: Up to 1,000m³/h

 

All-round unit with low operating costs

The 4-stage separator principle in OUPC ensures the optimale filtration solution, regardless the type of cooling lubricants, since every filter stage represents the optimale filter principle for each of the primary types of mists: oil mist, emulsion mist, minimal quantity lubrication and oil smoke.

The large surface of the washable pre-filter and self-draining filter cartridge ensure long service life and low pressure loss, which minimize costs for energy and filter replacements. The high separation degree of the third filter stage ensures very long life.

Compact and space-saving solution

The horisontal construction of OUPC 500 – 1010 provides an especially compact and space-saving filter solution for mounting directly on machining center due to height restrictions as a result of e.g. crane use over the machine. With integrated fan, the piping on the clean air side is also saved (where recirculation is permitted).

Advantages by removal of oil mists directly at the machine

  • The hazardous effects on breathing and skin are reduced.
  • Less risk of slippery floors and consequential accidents.
  • Fire risk as well as the risk of oil mist aerosols damaging electronics in the machines are minimized.
  • Cleaning and maintenance costs are reduced, since oil deposits in piping and on surfaces are avoided.
  • Energy consumption is reduced (reduced air speed in ventilation channels, when there are no heavy oil particles that must be kept airborn, no oil mist deposits on light sources).

Filter material:

Standard Material Filtration efficiency
Pre-separation in grease filter Pore filter 35 open-celled polyurethane
foam (washable)
Separated normally up to 30% of particles
Fine filtration in self-draining
cartridge filter
Cartridge filter ø325mm,
length 330/660mm,
G104A polyester/glassfibre
Separated more than 99% of particles
over 0.1µm
Fine filtration through HEPA-
absolute filter
HS-Mikro SFV
High Effeciency Particular Air filter,
microfilter (glassfibre) mounted
in metal frame
> 99,95% equal to filter class H13
according to DS EN1822

Pressure lost over the individual filter stages

Principle sketch for flow through oil mist separator type OUPC 510

Construction/surfaceoverflade:

Oil mist separator type OUPC is constructed according to:

  • Machine Directive 2006/42/EF
  • EMC Directive 2014/30/EU
  • Low Voltage Directive 2014/35/EU
  • Harmonized standards: EN 13854, EN 4414, EN 12100, EN 60204-1, EN ISO 13857
  • Further standards: ISO 3746

Filter cabinet is made in 2mm black steel plate
Surface powder enamelled RAL 7042/7011 structure

Further available

  • Siphon for drain cock
  • Outlet connection horizontal at the end instead of outlet grid without connection (only OUPC 510 and 1010)
  • Integrated magnet-operated motor protection for connection of remote-controlled start/stop

Oil mist filter type OUPC is available in the sizes as stated in the form below.

Please, contact us for assistance in selecting the optimal unit taking into consideration air volume, type and vo-lume of cooling lubricant, operation times etc.

Oil mist separator type OUPC 500 - 1000

1) Pore filter PPi35, 1x2m (08 179 800)
2) DIN-cartridge ø325x330mm, G104A (08 139 500)
3) DIN-cartridge ø325x660mm, G104A (08 139 510)
4) 1 pc. Minihelic-differential pressure manometer 0-3kPa (09 500 000) and 2 pcs Minihelic-differential pressure manometer0-0.5kPa (09 500 100)
5) Absolute filter in MDF-frame, HEPA/H13, 457x457x78cm (08 176 050)
6) Absolute filter in MDF-frame, HEPA/H13, 457x457x292cm (08 176 075)

Oil mist separator type OUPC 510 - 1010

Unit is in top equipped with a fan type VL, 3x400 VAC, 50Hz, 2800 rpm. The fan type is equipped with closed fan wheel and backward-curved straight self-cleaning blades, static/dynamic balanced according to ISO 14694 (BV3 G 6,3).

1) Pore filter PPi35, 1x2m (08 179 800)
2) DIN-cartridge ø325x330mm, G104A (08 139 500)
3) DIN-cartridge ø325x660mm, G104A (08 139 510)
4) 1 stk. Minihelic-differential pressure manometer 0-3kPa (09 500 000) og 2 stk Minihelic-differential pressure manometer0-0.5kPa (09 500 100)
5) Absolute filter in MDF-frame, HEPA/H13, 457x457x78cm (08 176 050)
6) Absolute filter in MDF-frame, HEPA/H13, 457x457x292cm (08 176 075)

Motor data:

Motor data > 0.75kW, 3x400V, according to IE3-motors.

Oil mist separator type OUPC 500

Oil mist separator type OUPC 510

Oil mist separator type OUPC 1000

Oil mist separator type OUPC 1010

Documents

Some of the documents require login. Order your login here.

Brochures
Instructions

Login to access the documents.

Pictures

Login to access the documents.

Drawings

Login to access the documents.

Go back